Concrete Sealing in Evanston: Sealing a Driveway Against Road Salt
A penetrating sealer is low cost protection for a sound driveway and does nothing for one that is already coming apart. We pour and replace concrete and we don't take sealing jobs, so here is the straight version: whether your slab needs it, which concrete sealer to buy, when Evanston's weather allows it, and who to call if you would rather not do it yourself.
Sealing a Concrete Driveway: Start With the Water Drop Check
Four questions, in order. The first one that stops you is your answer, and it may save you from buying a product you can't use. All you need is a cup of water and ten minutes on a dry day.
-
Is the Concrete Surface Still Sound?
Walk the slab and look for flaking, popped spots and crumbling edges. Sealer goes on good concrete. Quikrete's instructions say unsound or flaking concrete should be removed or repaired first.
Hard and intact: keep going Flaking or crumbling: skip to what sealer can't fix -
Is the Slab Past Its 28-Day Cure?
Most homeowner sealers want concrete about a month old. The details are in the new concrete section.
Older than a month or so: keep going Newer: wait -
Is There Old Sealer or Cure and Seal on the Slab?
Look for a sheen, a darker color in protected corners, or a coating peeling in the tire lanes. New driveways are sometimes finished with a cure and seal product, so ask whoever poured it. Penetrating sealers need bare concrete; Cemstone's guide says not to use them while a film-forming curing compound or sealer is still on the surface.
Bare concrete: keep going A film is present: a penetrating sealer can't get in -
Does Water Soak Into the Concrete?
Put drops of water on the worst worn tire lane, then on a protected spot near the house. Quikrete's test for previously sealed surfaces is this simple: if the water is absorbed, the surface is porous enough to accept sealer.
Soaks in and darkens: it can take a penetrating sealer Sits on top: something is still working, or still in the way
Don't read too much into beading. The classic bead test only works in one direction. Water that soaks in tells you something useful. Water that doesn't bead proves less: Foundation Armor's silane-siloxane data sheet says surface beading isn't a sealer benefit and isn't an indicator that the sealer is or isn't working, and that some treated surfaces never bead at all. Compare how fast water disappears in the tire lanes and in the protected spot. That difference is the best free evidence you have.
Penetrating vs Film-Forming Sealer: Choosing a Concrete Sealer
Sealers come in two families. Penetrating sealers soak in and sit inside the pores. Film-forming sealers leave a coat on top. For broom finished concrete in salt country, the guidance points one way: NRMCA's scaling guidance names silane or siloxane based breathable sealers, and Cemstone's 2026 guide calls penetrating sealers best for broom finished driveways, sidewalks and patios, and film-forming sealers ideal for decorative stamped or colored concrete.
| Type | What it does | Look | Slip when wet | Published recoat figure |
|---|---|---|---|---|
| Silane or siloxane (penetrating) | Soaks in and reacts in the pores to repel water and salt. Tremco and Sika list average penetration of about 0.30 and 0.35 inch for their 100% silanes. Breathable, no film. | Unchanged or nearly so | Sika's sheet shows the same skid number on broomed concrete before and after treatment: 90 and 90 | Foundation Armor SX5000: up to 7 to 10 years. PACA: reactive sealers may last 10 years or longer. |
| Silicate (densifier) | Reacts with the concrete to harden the surface. Prosoco's guide rates its water repellency low and points it at warehouse and polished floors. | No film | No film added | Prosoco says it does not need reapplying, but it is not a salt product |
| Acrylic (film-forming) | Forms a thin coat on the surface. Foundation Armor's AR500 darkens the concrete; Quikrete's cure and seal is satin. Good for color and stains. | Darker, satin to high gloss | Foundation Armor warns it may be slippery when wet and suggests a non-slip additive in the top coat | No fixed figure on the sheets we read. Prosoco says some sealers need recoating within 12 to 18 months. |
| Epoxy or urethane (film-forming) | A hard, thick film. Prosoco lists epoxy for warehouses and labs. Concrete Decor says both resist tire marks better than acrylic but are more prone to trapping moisture and turning white outdoors. | Glossy | Prosoco says high gloss epoxies can become dangerously slick when wet without grit or texture | None verified for driveways; these are rarely the right driveway product |
From Sikagard H 1000 (June 2025), Tremco Vulkem 100% Silane (September 2025), Foundation Armor SX5000 and AR500, Quikrete Acrylic Concrete Cure & Seal (October 2020), Prosoco's sealer guide (August 2025), Concrete Decor (2014), NRMCA CIP 2, and the Pennsylvania Aggregates and Concrete Association (PACA). Service life figures are what makers claim, not what a North Shore driveway has been shown to deliver.
The practical pick for most Evanston driveways is a silane, siloxane or blended penetrating sealer. It keeps the broom texture, leaves nothing on top for tires or shovels to lift, and lets the slab breathe. Pick a film-forming acrylic only if you want the darker look and accept the upkeep and the slip question that come with it.
Does New Concrete Need Sealer?
Not strictly, and we would rather say so than oversell it. Properly made air entrained concrete is built to survive winters unsealed. The Portland Cement Association salted test slabs at its outdoor facility in Skokie for 36 years, and an OxyChem summary of that work reports minimal scaling with sodium chloride and calcium chloride on concrete that was properly made, finished and cured, with time to mature before its first winter. OxyChem sells calcium chloride, so weigh that accordingly, but the point stands: mix and curing come first.
Sealer is extra margin on top. NRMCA's rules for preventing scaling say to consider a breathable sealer. PACA says sealers are designed to supplement, not replace, durable, properly cured concrete. A 2019 presentation by engineers at Simpson Gumpertz & Heger says sealers add margin, especially for concrete cast late in the season, and that the benefits likely outweigh the costs. Our new driveways are poured with an air entrained mix because Evanston's adopted code rates the area severe for weathering, and that mix is what does the heavy lifting. Sealing it afterward is inexpensive insurance, not a requirement.
How Long to Wait Before Sealing New Concrete
Follow your product's sheet, because they differ:
- 28 days: Foundation Armor and Cemstone.
- 30 days: Quikrete's silane-siloxane sealer. Bob Vila's guide says at least 30 too.
- 14 to 28 days: Sika asks for 80% of design strength, typically reached in that range.
- 7 days minimum: Tremco's Vulkem silane, adding that longer cures improve performance. Wisconsin's highway research also landed on at least seven days.
Concrete Decor makes a useful point about the 28 day habit: it has more to do with letting concrete dry than with strength, and cool, humid weather can push drying past that mark. One exception is cure and seal, which goes on right after finishing as a curing compound. Cemstone says you still need a separate sealing coat at least 28 days after placement.
Sealing a Late-Season Concrete Pour
Here is a catch few guides mention. A slab poured in late fall can't meet a 28 day wait and a 50°F limit before winter, so home center sealers are usually out until the next warm season. Don't skip the protection that matters more: keep deicers off it that first winter, as NRMCA advises, and use clean sand for traction. If you want it sealed sooner, ask about a professional silane; the Sika and Tremco sheets allow a shorter cure and much colder application. Then look at the slab again the following year.
Concrete Driveway Sealer vs Road Salt, Tires and Plows
A driveway takes a harder beating than any other slab on the property, and each of its problems treats a sealer differently.
How Salt and Freeze-Thaw Scale Driveway Concrete
Scaling starts with water. NRMCA explains that saturated concrete freezes, the water expands, and the stress builds with each cycle. Deicers make it worse by raising saturation at the surface and adding freeze and thaw cycles. The microscopic bubbles in air entrained concrete give that ice somewhere to go. Evanston's adopted code rates the area severe for weathering, and the salt finds your driveway even if you never buy a bag: the city's Public Works page says primary streets get rock salt during snowfall, secondary streets a reduced rate and residential streets as needed, with brine, BeetHeet or calcium chloride mixed in as needed. It also says curb snow from city plows is unavoidable. That salted slush ends up on your tires and at the foot of your drive.
What a Penetrating Concrete Sealer Does Against Salt
It slows the water down. In a Wisconsin Highway Research Program study published in 2020, untreated lab samples of Wisconsin paving concrete reached critical saturation in 23 days; with a 40% silane applied after seven days, that took 218 days. On in-service pavement joints the effect faded with years of service, but sealed joints still beat unsealed ones after more than eight years. Manufacturers report similar lab results: Sika lists a 96% reduction in absorbed chloride at its heavier coverage rate and Tremco 93.7%, both on the same highway lab test.
Now the limits. Those tests are on lab samples and pavement, not your driveway. The Federal Highway Administration's 2018 brief says certain penetrating sealants may provide a barrier and offer some level of protection, and said lab studies and field monitoring were still underway. And the engineers behind that 2019 presentation put the bigger rule in one line: nothing protects saturated concrete, so let it dry. A sealer applied to a damp slab, or a slab that sits in meltwater, isn't getting that result.
Hot Tire Pickup on Film-Forming Driveway Sealer
Hot tires can pull a film off the slab. Concrete Decor says the most important factor is how well the sealer is stuck to the concrete, and that acrylics do worse than epoxies and polyurethanes. Foundation Armor says plainly that its AR500 acrylic does not stop hot tire pickup, and Prosoco says water-based acrylics may have less resistance to tire marking. A penetrating sealer has no film for a tire to grab, which is one more reason it suits a driveway.
Shovels, Plows and Driveway Sealer Wear
Anything on top of a slab is in the path of the shovel and the plow blade. A film takes that wear directly, and Cemstone notes that sealers wear down from traffic and weather. A penetrating sealer sits below the surface, and PACA says reactive sealers generally wear away only if the surface itself does. If you hire a plow, that favors a penetrating product. It does not mean the plow can't hurt the slab: a steel edge can still chip joints and edges.
Deicers on Sealed Concrete
A sealer doesn't change the rules on what you spread. They are the same rules as for bare concrete:
- First winter: avoid deicers. NRMCA's rule is the first winter; PACA says concrete under a year old. Use clean sand for traction.
- Rock salt and calcium chloride: NRMCA considers both acceptable for concrete, in moderate amounts. More is not better. The city says it is recognized as a Salt Smart Community, and the Salt Smart Collaborative adds that no salt product on the market is completely harm free.
- Ammonium products: never. NRMCA and PACA both warn that ammonium sulfate and ammonium nitrate destroy concrete surfaces. Read the back of the bag, because many deicers say "safe" on the front.
- Magnesium-based salts: NRMCA says not to use them, and notes they get tracked onto concrete from pretreated roads. PACA lists magnesium chloride among the deicers shown to cause much higher rates of deterioration.
- Liquid and concentrated products: FHWA flags concentrated calcium and magnesium chloride solutions in particular, especially where they pool in joints that don't drain.
- Rinsing: NRMCA suggests hosing off salt deposited by cars on driveways when conditions permit. Keep meltwater from pooling; poor drainage makes the exposure worse.
Sealing a Patio or Walk: Slip Resistance and Looks
A backyard patio usually sees less salt than a driveway, so the decision shifts toward stains, color and footing.
- Footing comes first. Penetrating sealers leave the broom texture alone. Prosoco warns that glossy coatings get slick when wet unless textured. On a shaded walk or a sloped entry, that's the reason to skip a gloss film. If you want one anyway, use a non-slip additive; our stamped concrete page makes the same point about the grit additive in decorative sealers.
- Decide on the look before you buy. An acrylic darkens the slab and can't easily be undone. Test a hidden corner first; Tremco and Sika both say to give a test area 5 to 7 days before judging it.
- Exposed aggregate is a good candidate. Quikrete calls its silane-siloxane sealer particularly suitable for exposed aggregate.
- The joint against the house isn't a sealer job. A surface sealer won't close that gap. It takes backer rod and flexible sealant, covered in our concrete repair guide.
Stamped work plays by its own rules. There the sealer really is part of the finish, and our stamped concrete page covers why it matters, the resealing schedule and the grit additive.
How Often to Seal Concrete
There is no single honest number. Published figures run from every year to every decade, because they mix different products and different kinds of writers.
| Source | What it covers | What it says |
|---|---|---|
| Foundation Armor data sheets | SX5000 silane-siloxane; SC25 siliconate | Up to 7 to 10 years; up to 3 to 5 years |
| PACA | Reactive penetrating sealers | Generally wear away only with the surface, which may be 10 years or longer |
| Bob Vila, February 2023 | Concrete sealers generally | Every 2 to 3 years; more often with heavy use or extreme weather |
| LawnStarter, October 2026 | Concrete driveways | Every 1 to 10 years |
| Cemstone, 2026 | Driveways, patios, walkways | Follow the manufacturer's instructions |
How to Tell When a Driveway Needs Resealing
Treat the maker's number as a ceiling, not a promise. Wisconsin's pavement research found sealer effectiveness decreases with years of service. Instead of trusting the calendar, run the water drop check each fall on the tire lanes and at the foot of the drive, where wear and salt are worst. If water soaks in there and not near the house, it is time. If water still stays out, leave it alone; Quikrete says not to use its sealer on a surface that won't take it.
Recoating Concrete Sealer: Match What Is Already There
Write down what you used. Products don't mix freely. Foundation Armor says its SX5000 is for unsealed surfaces and shouldn't go over a recently applied water repellent or any film-forming sealer. Its AR500 acrylic can go over solvent-based acrylic only. If you inherited a sealed driveway and don't know what's on it, test a small patch before you buy five gallons.
When to Seal Concrete in Evanston
NRMCA says late summer, with a few dry days before you apply, is the ideal time. Here, that also puts the job ahead of the first salt. The rest of the year works only as far as your product's label allows.
Workable once the slab is dry. Spring rain has had time to rinse winter's salt, and Foundation Armor warns against sealing with salt water still in the pores. Avoid the hottest days.
The target. Warm nights, a slab that has dried out, and plenty of room before salt season.
Still good, while nights hold above your product's limit. This is the deadline for most homeowner products.
Done for home center sealers. Salt on the slab, cold nights and damp concrete all work against you. Wait.
| Product (data sheet) | Type | Temperature | Moisture | Vehicles |
|---|---|---|---|---|
| Quikrete Waterproofing Sealer 8800-05 (November 2020) | Water-based silane-siloxane | Air and surface 50°F to 90°F; nothing below 50°F expected within 24 hours | No rain or heavy dew expected within 24 hours | Not listed |
| Foundation Armor SX5000 | Solvent-based silane-siloxane | Air and surface 55°F to 85°F | Dry 24 hours after washing; kept dry 24 hours after | 24 to 48 hours |
| Quikrete Acrylic Cure & Seal (October 2020) | Water-based acrylic | Nothing below 50°F expected within 24 hours | No rain or heavy dew expected within 24 hours | Not listed |
| Foundation Armor AR500 | Solvent-based acrylic | 45°F to 85°F; early evening only | Dry 24 hours after washing | 24 to 48 hours |
| Sikagard H 1000 (June 2025) | Professional 100% silane | 20°F and rising, up to 95°F; frost free | No rain within 4 hours; slightly damp surface allowed | Not listed |
| Tremco Vulkem 100% Silane (September 2025) | Professional 100% silane | Not below 20°F; no frost | No rain within 4 to 6 hours; 24 hours of drying after rain | 2 to 4 hours |
What that means here: the night sets the limit. A mild October afternoon followed by a 45°F night fails Quikrete's rule even if the afternoon felt fine, and a slab can stay colder than the air after a cold snap. Between washing and curing, a homeowner product asks for two or more dry days in a row. Look at the forecast before you buy, not after. If you miss the window, a slab that goes one more winter unsealed is better off than one sealed damp or cold, and you can take it up again next year.
DIY or a Concrete Sealing Company?
A penetrating sealer on a sound, bare driveway is a fair do it yourself afternoon, spread across a couple of days for drying. There is no reason to pay for labor if you are comfortable with a sprayer and a forecast. Here is how the job goes.
Clean the Concrete
Remove oil, dirt and old contaminants. Quikrete says to clean first; Foundation Armor says pressure washing is typically enough, with spot treatment for deep stains. Rinse cleaners off completely. Leftover residue is a contaminant.
Let the Slab Dry
Foundation Armor asks for at least 24 hours after washing, and warns that a slab can feel dry while the pores are still wet.
Test a Small Patch of Sealer
Sika calls for a test area of at least 5 by 5 feet and 5 to 7 days before judging it. This is where you catch darkening or a surface that won't absorb.
Apply Sealer Evenly, No Puddles
Use a low pressure sprayer or roller as the label says. Quikrete allows a second coat 5 to 10 minutes after the first, while it is still wet. Foundation Armor warns that over-application leaves dark spots. Cover plants and anything you don't want sprayed.
Keep the Sealed Slab Dry
Plan on at least 24 hours without rain, and keep cars off for as long as the label says.
Write Down the Sealer You Used
Product, date and coverage. The next person to reseal this slab will need it, and that may be you.
Read the safety sheet before you start. Solvent-based sealers smell strong; Foundation Armor calls for protective equipment and ventilation, and warns that its solvent acrylic is flammable. For material, Quikrete's 75 to 150 square feet per gallon means about 3.5 to 7 gallons for one coat on a 500 square foot driveway.
What a Concrete Sealing Company Adds
- Stripping. Taking old film-forming sealer off takes a stripper, grinding or sandblasting. That alone can justify hiring it out.
- Professional products. Silanes like Sikagard H 1000 and Vulkem come in 5 gallon pails and larger, and their sheets mostly assume spray equipment.
- A wider weather window. Those same products can go on far colder than home center sealers.
- Even coverage on a big slab. Long driveways and connected walks show mistakes that a small test patch doesn't.
Questions for Concrete Sealing Companies Near Me
- Which exact product will you use, and can I see the data sheet?
- Penetrating or film-forming, and why for this slab?
- How will you clean it, and how long will it dry before you seal?
- How do you know what is already on the concrete?
- What coverage rate and how many coats?
- What temperature and rain limits apply, and will you reschedule if they aren't met?
- Do you handle cracks and joints first, or is that separate? Tremco's sheet wants them dealt with before sealing.
- Is cleaning in the price? Some contractors include it and some don't.
Be wary of anyone promising a lifetime seal. No data sheet we read makes that claim for a driveway.
Concrete Sealing Cost: National Figures and What Drives Them
We don't do sealing jobs, so these are published figures, not our prices and not a quote for your slab. Most are national, some are a few years old, and all of them are useful only for checking whether a bid is in a normal range.
| Item | Published figure | Source |
|---|---|---|
| Professional sealing of concrete | $0.85 to $2.13 per square foot | LawnStarter, updated October 2026; same range in Bob Vila, April 2024 |
| Professional cleaning and sealing | $1.20 to $1.75 per square foot | Bob Vila, updated February 2023 |
| Cleaning and sealing | $1 to $3 per square foot | HomeGuide's 2026 rates, as reported by ThePricer, September 2026 |
| 400 square foot driveway | $400 to $800 | HomeGuide, as reported by ThePricer, September 2026 |
| 576 square foot driveway | $580 to $1,200 | HomeGuide, as reported by ThePricer, September 2026 |
| 500 square feet in Chicago | $960 | Bob Vila, updated February 2023 |
| Do it yourself cleaning and sealing | $0.20 to $0.75 per square foot | Bob Vila, updated February 2023 |
| Pressure washing, if not included | $0.27 to $0.39 per square foot | LawnStarter, updated October 2026 |
| Replacing a concrete driveway, for comparison | $5 to $24 per square foot, including labor | Fixr, updated January 2025 |
What moves a sealing bid:
- Prep. A wash is cheap. Stripping an old film is the expensive part.
- The sealer. Active content and type vary a lot from pail to pail, so compare the data sheets along with the prices.
- Coats and porosity. A rough, thirsty slab drinks more product per square foot.
- Size and access. Walks, steps and tight spots cost more to mask and spray than an open driveway.
Here is the admission that costs us something. Sealing an existing driveway costs far less than replacing it; compare the rows above. On a sound slab, spending on sealer and going easy on salt is a better first move than calling us. If it buys your driveway more years, that is money you keep.
What Sealer Can't Fix on a Concrete Slab
Sealer is prevention. Sika's own sheet says its silane will not stop water from getting through unsound or cracked surfaces. If your slab stopped at question one of the water drop check, this is where to go next.
| What you see | Why sealer won't help | Go here |
|---|---|---|
| Surface flaking or scaled across the slab | Sealer won't rebuild a lost surface. NRMCA says minor scaling is cosmetic, and that light to moderate scaling can take a bonded repair over sound concrete. Sealers have to come off before a resurfacer goes on, and Foundation Armor says removing its penetrating sealer isn't recommended, so don't seal a slab you plan to top. | Resurfacing a scaled slab |
| Open cracks or failed joints | Penetrating sealers treat the pores and don't bridge a gap. Joints and cracks need the right sealant, and Tremco's sheet wants that done before sealing. | Telling crack types apart |
| A section sunk or tipped | The slab's position is the problem, and water will keep running where it shouldn't. | Lifting sunken concrete |
| Water standing on the slab | Quikrete says not to use its sealer in areas prone to standing water. NRMCA says poor drainage increases the severity of exposure. Fix the water first. | Pitch and drainage fixes |
| Soft, crumbling or heaved driveway | Nothing sound is left to protect, or the cause is under the slab. | Driveway replacement |
| Salt worn garage slab | A garage floor is a different job, and our page explains what is worth fixing there. | Garage floor repair |
Not sure your slab is worth sealing?
Text a close photo of the worst spot and a wide one of the whole slab. We will tell you whether it looks like a sealing job for you or a sealing company, or something past that point.
(847) 380-8138Concrete Driveway Sealing Near Me: Who Does What
We are a flatwork contractor, and we don't take jobs sealing existing driveways, patios or walks. If that is what you need, you want a sealing company or a free weekend, and we would rather tell you that up front. When a slab is past sealing, replacement is the work we do. The related work on this site:
- Stamped concrete, where sealer is part of the finish and the page covers the resealing schedule.
- Garage floor repair, which includes filling and sealing cracks.
- New concrete driveways, poured with an air entrained mix for this climate.
- Our concrete repair guide, for joint and crack sealants and the other small fixes.
- Our concrete resurfacing guide, for slabs that have already scaled.
Text a photo to (847) 380-8138 or use the form. Leave the service menu on Not Sure and describe the slab and where it is.
Get a Free Estimate
Tell us about the project and we will get back to you within one business day. Prefer to talk? Call or text (847) 380-8138.
Concrete Sealing Questions
It slows it down; it does not stop it. A penetrating sealer cuts how much salt water soaks into the surface, and lab work such as the Wisconsin Highway Research Program study shows concrete taking far longer to reach a damaging level of saturation once treated. But sealers supplement good concrete, they do not replace it, as the Pennsylvania Aggregates and Concrete Association puts it. Go light on deicer, rinse the driveway when you can, and keep meltwater from standing on it.
That depends on the night, not the afternoon. Quikrete's water-based silane-siloxane sealer cannot go down if temperatures below 50°F are expected within 24 hours, and Foundation Armor's SX5000 needs 55°F. Those windows close in fall. Professional silanes such as Sikagard H 1000 and Vulkem go on at 20°F and up on a frost free surface. If you are past your product's limit, wait for late spring rather than forcing it.
A penetrating sealer should not. Sika's data sheet shows the same skid number on broomed concrete before and after treatment, because there is no film on top. A film-forming acrylic can. Foundation Armor warns that its wet look acrylic may be slippery when wet and suggests a non-slip additive in the top coat. The glossier the film, the more that matters on a sloped driveway.
No. A penetrating sealer has to soak into bare concrete, and a film blocks it. Foundation Armor says not to put SX5000 over a film-forming sealer, and Cemstone says penetrating sealers should not be used while a sealer or film-forming curing compound is still on the surface. The film has to wear off or be stripped first. Foundation Armor lists a paint stripper, grinding or sandblasting for removing cured acrylic.
Follow the label, because the range is wide. Foundation Armor lists wheel traffic at 24 to 48 hours for both its SX5000 silane-siloxane and its AR500 acrylic. Tremco's Vulkem silane data sheet lists 2 to 4 hours for foot and wheel traffic. Cool, humid weather stretches those times, and the sheets we read all want it rain free while it cures.
Not as a job of its own. We do not seal or reseal existing driveways, patios, walks or slabs. We pour and replace flatwork. Sealer shows up in our work in two narrower places that have their own pages: new stamped concrete, where it is part of the finish, and garage floor repair, which includes sealing cracks. For a plain driveway, patio or walk, sealing is usually a homeowner job or a sealing company's job.
Slab Past Sealing? Check the Concrete Before You Spend
Evanston Concrete Co is a concrete contractor in Evanston serving the North Shore. Send a photo and we will tell you straight whether it needs a sealer, a repair, or a new pour.
(847) 380-8138